Sodium Lauryl Ether Sulfate

Sodium Lauryl Ether Sulfate — chemical structure

Sodium lauryl ether sulfate (SLES), also called sodium laureth sulfate, is an anionic surfactant made from ethoxylated lauryl alcohol. It is the most widely used foaming and cleansing ingredient in shampoos, body washes, hand soaps, dishwashing liquids and liquid detergents. This page covers its formula and structure, how it is made, its properties, uses, safety and the grades buyers can order.

Key facts
  • Other names: sodium laureth sulfate, SLES, sodium dodecyl ether sulfate; INCI name Sodium Laureth Sulfate.
  • Formula: CH3(CH2)11(OCH2CH2)nOSO3Na, with n usually 1–3 (2EO and 3EO grades are common).
  • CAS numbers in use: 68585-34-2 and 9004-82-4.
  • Type: anionic surfactant; foaming agent, cleanser, wetting agent and emulsifier.
  • Commercial forms: about 70% active paste or 25–30% active solution.

Sodium Laureth Sulfate vs Sodium Lauryl Ether Sulfate

They are the same compound. “Laureth” is simply a contraction of lauryl ether, which describes the ethoxylated lauryl alcohol SLES is made from. Whether a formula, label or batch record says sodium laureth sulfate or sodium lauryl ether sulfate, it refers to SLES. It should not be confused with sodium lauryl sulfate (SLS), which is not ethoxylated; see SLES vs SLS.

Chemical Formula and Structure

SLES has the general formula R(OCH2CH2)nOSO3Na and belongs to the family of sodium alkyl ether sulfates:

  • R is a C12–C14 fatty chain: the oil-loving (hydrophobic) tail that holds grease and soil.
  • (OCH2CH2)n is a short ethylene oxide chain, usually 1–3 units. It makes the head group larger and more hydrated, which is why SLES is milder and more hard-water tolerant than SLS.
  • OSO3Na is the sulfate head that dissolves in water and carries the negative charge.

Because the number of ethylene oxide units varies from molecule to molecule, SLES is a mixture; its molecular weight depends on the average degree of ethoxylation (about 376 g/mol for an average of 2 EO and about 420 g/mol for 3 EO).

How SLES Is Made

  1. A fatty alcohol, from palm kernel or coconut oil or from petrochemical sources, is ethoxylated with ethylene oxide.
  2. The ethoxylated alcohol is sulfated, usually with sulfur trioxide.
  3. The acid is neutralised with sodium hydroxide to give SLES.

Ethoxylation can leave traces of 1,4-dioxane, so good producers remove it by process control and vacuum stripping; see the safety section below.

Physical and Chemical Properties

PropertyTypical behaviour
AppearanceClear to pale yellow liquid (dilute) or viscous paste (about 70%)
SolubilitySoluble in water, forming micelles; insoluble in oils and most organic solvents
pH (10% solution)6.5 – 8.5 for Green Agrochem grades
Gel rangeConcentrated solutions pass through a thick gel phase, so the 70% paste must be diluted in steps
Viscosity with saltDiluted SLES thickens as sodium chloride is added, up to a peak, then thins again (the “salt curve”)
Hard waterKeeps foaming and cleaning better than SLS or soap
Thermal behaviourNo boiling point; decomposes before boiling; stable under normal storage

Anionic Surfactants Compared

SurfactantMain useFoamMildness
SLESShampoo, body wash, dish liquidHighMilder than SLS
SLSToothpaste, cleanersHighMore irritating
LASLaundry detergentsHighModerate
Ammonium lauryl ether sulfate (ALES)ShampoosHighSimilar to SLES

Uses of SLES

  • Personal care: shampoos, body washes, shower gels, liquid hand soaps, facial cleansers and toothpaste. See SLES in shampoo formulation.
  • Household cleaning: hand dishwashing liquids, liquid laundry detergents and all-purpose cleaners. See SLES in liquid detergents.
  • Industrial: metal and floor cleaners, degreasers, car-wash products, textile processing and emulsion polymerization for paints, adhesives and coatings.

Why Formulators Choose SLES

  • Rich, stable foam across a wide dilution range; see SLES foaming properties.
  • Milder than SLS at the same active level, especially with an amphoteric co-surfactant; see SLES mildness.
  • Easy to thicken with salt, which keeps formulas low-cost.
  • Compatible with amphoteric and nonionic co-surfactants such as cocamidopropyl betaine, but not with cationic surfactants.
  • Hard-water tolerant and cost-effective for mass-market products.

Working With the 70% Grade

StepGuidance (SLES 70% TDS)
DilutionDilute with water or the liquid phase under gentle mixing before adding salt or thickener
Avoid gellingAdd slowly to avoid local high-concentration gel
ViscosityBuild with sodium chloride or a PEG-based thickener; run a salt-curve trial for each new formula
StorageAvoid freeze/thaw cycles; warm gently and mix if the product looks hazy after cold storage

Safety and Regulation

  • Skin and eyes: the Cosmetic Ingredient Review found sodium laureth sulfate to be an irritant but not a sensitiser, and safe in cosmetics when formulated to be non-irritating (Int. J. Toxicol. 2010; 29(4 Suppl):151S–161S).
  • 1,4-dioxane: a possible trace by-product of ethoxylation. Buyers should set a limit and test method in the specification and check destination-market rules; see SLES safety.
  • Handling: concentrated SLES irritates skin and eyes; use gloves and eye protection and follow the SDS.

Environmental Profile

SLES is readily biodegradable under aerobic conditions and is removed efficiently in conventional wastewater treatment; degradation is slower without oxygen. At high concentrations it is toxic to aquatic organisms, so untreated discharge should be avoided. It can be made from renewable coconut or palm kernel oil or from petrochemical alcohols; buyers with sustainability targets can ask about the feedstock and certified (for example RSPO) supply.

Our SLES Grades

ParameterSLES 70% (GAC-SLES-70)SLES 30% (GAC-SLES-30)
AppearancePale yellow to amber liquidPale yellow to amber liquid
Active matter70 – 75%25 – 30%
pH (10% solution)6.5 – 8.56.5 – 8.5
Ionic characterAnionicAnionic
SolubilitySoluble in water; insoluble in oils and most organic solventsSame
INCI nameSodium Laureth SulfateSodium Laureth Sulfate
PackingDrums (200 – 220 kg); IBC and bulk on requestDrums and bulk containers

Typical values from the current TDS. Batch results are on the COA. CAS numbers used for SLES: 68585-34-2 and 9004-82-4.

Guides in This Topic

Applications

Properties and safety

Buying

Frequently Asked Questions

Is sodium laureth sulfate the same as sodium lauryl ether sulfate?

Yes. Sodium laureth sulfate and sodium lauryl ether sulfate are two names for the same compound, SLES. “Laureth” is a contraction of lauryl ether, the ethoxylated lauryl alcohol it is made from.

What is the chemical formula of SLES?

SLES has the general formula CH3(CH2)11(OCH2CH2)nOSO3Na, often written R(OCH2CH2)nOSO3Na, where R is a C12–C14 fatty chain and n, the number of ethylene oxide units, is usually 1–3. Because n varies, SLES is a mixture rather than a single molecule.

Is SLES an anionic surfactant?

Yes. Its sulfate head group carries a negative charge in water, so SLES belongs to the anionic surfactants, together with SLS, LAS and ammonium lauryl ether sulfate.

What is SLES used for?

Mainly as the primary foaming and cleansing surfactant in shampoos, body washes, hand soaps, dishwashing liquids, laundry detergents and all-purpose cleaners, and in industrial cleaners, textile processing and emulsion polymerization.

What active content is SLES supplied at?

Usually as a concentrated paste of about 70% active matter or as a 25–30% solution. Green Agrochem supplies GAC-SLES-70 (70–75% active) and GAC-SLES-30 (25–30% active).

Buy SLES

Related: SLES vs SLS · SLES suppliers · SLES in dishwashing liquid

Categories: